View question



Asked On2019-07-09 09:48:38 by:KAPILJHADE

Taged users:


Likes:
Be first to like this question

Dislikes:
Be first to dislike this question
  Like  Dislike

Comments


Type your comment here



Checkout our YouTube channel for video tutorials and learn more about Eduladder.

New updates
Searching for : A resistance of 12 ohm , inductance of 0.1 H and a capacitance of 100 micro-farad are connected in series across ac 220 V, 100 Hz supply. Calculate the current and its power factor , power consumed and phase angle mentioning the whether it is leading or lagging.Date:2023-01-29 23:16:15Done by:Anonymous user(Visitor)

Searching for : A resistance of 12 ohm , inductance of 0.1 H and a capacitance of 100 micro-farad are connected in series across ac 220 V, 100 Hz supply. Calculate the current and its power factor , power consumed and phase angle mentioning the whether it is leading or lagging.Date:2023-01-29 23:15:57Done by:Anonymous user(Visitor)

Searching for : A resistance of 12 ohm , inductance of 0.1 H and a capacitance of 100 micro-farad are connected in series across ac 220 V, 100 Hz supply. Calculate the current and its power factor , power consumed and phase angle mentioning the whether it is leading or lagging.Date:2023-01-29 23:15:28Done by:Anonymous user(Visitor)

View All

Similar Questions


True stress - true strain behavior of a metal is given by the flow curve equation o=1750e^0.37 , where o is in MPa. The true stress at necking (in MPa, rounded off to the nearest integer) is ___________________.
0 Answer

The true stress (σ) - true strain (  ) diagram of a strain hardening material is shown in figure. First, there is loading up to point A, i.e., up to stress of 500 MPa and strain of 0.5. (Gate 2018 Mechanical engineering)
1 Answer

Consider the stress-strain curve for an ideal elastic-plastic strain hardening metal as shown in the figure. The metal was loaded in uniaxial tension starting from O. Upon loading, the stress-strain curve passes through initial yield point at P, and then strain hardens to point Q, where the loading was stopped. From point Q, the specimen was unloaded to point R, where the stress is zero. If the same specimen is reloaded in tension from point R, the value of stress at which the material yields again is _________ MPa.
0 Answer

The true stress (in MPa) versus true strain relationship for a metal is given by (Gate 2018 Mechanical engineering)
1 Answer

In a linearly hardening plastic material, the true stress beyond initial yielding (gate 2018 Mechanical engineering)
1 Answer

In stress strain curve of mild steel Ultimate Tensile Stress is
1 Answer

Consider the singly reinforced beam shown in the figure below:At cross-section XX, which of the following statements is TRUE at the limit state? - gate civil 2017
1 Answer

For the following statements: P – The lateral stress in the soil while being tested in an oedometer is always at-rest. Q – For a perfectly rigid strip footing at deeper depths in a sand deposit, the vertical normal contact stress at the footing edge is greater than that at its centre. R – The corrections for overburden pressure and dilatancy are not applied to measured SPT-N values in case of clay deposits.
0 Answer

The S-N curve for a steel is shown below. If the stress ratio, (σmin/σmax) = −0.8, the maximum stress (in MPa, rounded off to the nearest integer) that the steel can withstand for infinite fatigue life is ____________.
0 Answer

As compared to the engineering stress-engineering st rain curve, the true stress-true strain curve for a given material, GATE- Metallurgical Engineering- 2013
1 Answer

In the engineering stress-strain curve for mild steel, the Ultimate Tensile Strength (UTS) refers to
1 Answer

D etermine the correctness or otherwise of the following Assertion [a] and the Reason [r]. [a]: The work factor of silk fibre is greater than 0.5. [r]: The work factor is calculated by assuming the following as the stress-strain curve of silk fibre.
1 Answer

The uniaxial stress-strain behavior of a rock sample is shown in the figure. The elastic modulus E is 20,000 MPa. If p  is the plastic strain, the value of the damage parameter D (rounded off to two decimal place) is _________.
0 Answer

For the state of stress shown in the figure, the normal stress, σn , on a plane inclined at 45 degrees to the x-axis is _________ MPa (round off to the nearest integer).
0 Answer

Assertion [a]: The streamlines in a free vortex flow are concentric circles. Reasoning [r]: There exists only radial component for the velocity field in a free vortex flow.
0 Answer

In a soil specimen, the total stress, effective stress, hydraulic gradient and critical hydraulic gradient are ,  ', i and ic, respectively. For initiation of quicksand condition, which one of the following statements is TRUE?
0 Answer

A metallic rod of diameter 0 d is subjected to the tensile test. The engineering stress and the true stress at fracture are 800 MPa and 900 MPa, respectively. The ratio of the rod diameter at fracture f d to the initial diameter 0 d is ______ (round off to 2 decimal places)
0 Answer

Assertion (a): The 18O/16O ratio in natural systems can be used as a thermometer. Reason (r): The fractionation of 18O/16O depends on temperature. -gate Geology & Geophysics 2017
1 Answer

Frustration is one of the sources of psychological stress. (True/False) (PSYCHOLOGY-CBSE-2018)
1 Answer

Consider the following statement about the linear dependence of the real valued functions
1 Answer

Notes

CE2257 STRENGTH OF MATERIALS LABORATORY

VTU SYLLABUS 2010 STRENGTH OF MATERIALS (COMMON TO CV/TR/EV/CTM) [10CV33] Engineering.

CE2201 MECHANICS OF SOLIDS

CE2251 SOIL MECHANICS

10me34 Mechanics of materials

CE2252 STRENGTH OF MATERIALS

7 of Fire: Stress

CE2049 SMART STRUCTURES AND SMART MATERIALS | ANNA UNIVERSITY BE CIVIL ENGINEERING 8th SEMESTER SYLLABUS 2008 REGULATION

10ee82 Notes downloadable

Zero knowledge protocol and proof system.