An-ideal-structure-for-tunnel-is-anticline-unconformity-syncline-and-fault

Search result related to
An ideal structure for tunnel is anticline unconformity syncline and fault

Notes

CE 2046 WIND ENGINEERING

Life Path Number 8

EC2151 ELECTRIC CIRCUITS AND ELECTRON DEVICES

Ketu in Third House

Observer Based Sensorless Control

Magneto-optical current transformer technology

Moon in twelfth House

MCSE-102 ADVANCED DATA STRUCTURE AND ALGORITHM

Data Structures using Python

BTD

Questions

Horizontal slickensides are observed on the surface of a vertical fault. What is the type of fault? (-Gate geology and geophysics)
1 Answer

Explain the following: a) Unconformity (Jan-2013) b) Dip and Strike
c) Normal and Reverse fault d) Drag fold
(May/June2012)
1 Answer

If the rake of net slip of an inclined fault is 90°, the fault is GATE-Geology and Geophysics-Question-2012
1 Answer

Fault Masking is
1 Answer

A 30 kV, 50 Hz, 50 MVA generator has the positive, negative, and zero sequence reactances of 0.25 pu, 0.15 pu, and 0.05 pu, respectively. The neutral of the generator is grounded with a reactance so that the fault current for a bolted LG fault and that of a bolted three-phase fault at the generator terminal are equal. The value of grounding reactance in ohms (round off to one decimal place) is ________.
0 Answer

Eparchean unconformity separates geological units of GATE-Geology and Geophysics-Question-2012
1 Answer

The insitu stress field around a circular tunnel is shown in the figure. Points A and B are located at the boundary of the tunnel. If the tangential stress at Point A is 3 times of that at Point B, the value of insitu stress ratio, k is _________.
0 Answer

when does a program shows a segmentation fault?
1 Answer

Which of the following is false?
1 Answer

With a diagram discuss the steps involved in handling a page fault??
2 Answer

The later in the development life cycle a fault is discovered, the more expensive it is to fi x. why?
1 Answer

(Gate 2018 Mechanical engineering)An ideal gas undergoes a process from state 1 ( T1 = 300 K, 1 p = 100 kPa) to state 2 ( T2 = 600 K, 2 p = 500 kPa). The specific heats of the ideal gas are : cp = 1 kJ/kg-K and cv = 0.7 kJ/kg-K. The change in specific entropy of the ideal gas from state 1 to state 2 (in kJ/kg-K) is ___________
1 Answer

What information need not be included in a test incident report:
1 Answer

After migration, an anticline observed on an unmigrated seismic section becomes -gate Geology & Geophysics 2017
1 Answer

The most suitable hydraulic structure for conveying water from higher elevation to lower elevation across the earthen bund isGate-Agricultural-2016
1 Answer

Add a note on Angular Unconformity. (Dec 2012) (Jan-2013) (Dec-2013)
1 Answer

To simulate the aerodynamic forces on a cylinder of 1 m diameter due to a uniform air flow of 1 m/s at standard temperature and pressure (STP), low-speed wind tunnel experiments at STP are conducted on a 0.1 m diameter cylinder. The free stream air speed in the wind tunnel experiments should be _______ m/s (round off to the nearest integer).
0 Answer

The INCORRECT statement about the solid-state structure of CsCl and CaF2 is:
1 Answer

Adiabatic work of 200 kJ is done on ideal gas of mass m = 1 kg (Cv=1000 j/kgk ), which is stored in a rigid container at a pressure of 100 kPa and temperature 300 K.
1 Answer

As compared to large earthquakes, small earthquakes are: (-Gate geology and geophysics 2014)
1 Answer

Speaks